- EOL
|
Attention! The sale of the product has been completed. Checkother pcDuino minicomputers in this category. |
Description
PdDuino3 Nano minicomputer with a powerfulARM Cortex A7 dual-core 32-bit 1 GHzprocessor. The board has1 GB of DRAM,built-inEthernet Gigabitport,HDMI1.4 1080p/30Hz and2 xUSB 2.0, 4GBFlash memory,microSD cardconnectors,SATA connector,IR receiver. Works with Linux or Android systems. The device is compatible withArduino overlays.
The device has 2 USB 2.0 ports, HDMI, Ethernet port and many others.
What do you need to run pcDuino3 minicomputer?
- MicroSD memory cardor built-in memory - the media on which theoperatingsystem will be installed.
- The power supply:
- 5 V / 2 Afor the minicomputer itself
- 5 V / 3 A - for a minicomputer with attached overlays
- HDMI cable - toconnect the device to a monitor
- Mouse and keyboard- to control and enter data into the device
- Connected internet - for software download
Operating system
pcDuino3 Nano works with Linux and Android systems. The device can be a microSD card.
|
Installation of the system is very easy -check the manual! |
Communication
pcDuino3 Nano has basic communication interfaces that can be found in PC-class office computers. The user has it at his disposal:
- two USB 2.0 connectors,under which you can connect e.g. a mouse, a keyboard, a WiFi card or a flash drive. If it turns out that there are too few sockets, you can increase their number usingan external USB HUB.
- Ethernet socket, i.e. the possibility of direct connection to the LAN.
- microSD slot- a slot for a microSD memory card on which the operating system can be installed.
- SATA connector- allows to connect an external hard drive
- Arduino connectors- compatible with Arduino caps
- MIPI camera connector
pcDuino3 Nano has amicroSD memory cardslot next to the SATA connector.
The card is not included in the set and can be purchased separately.
Power supply
The system uses the microUSB connector as its power source. The manufacturer recommends that the voltage given on the connector should be 5.0 V, while the current capacity of the power supply used should be at least 2.0 A. In our offer you will finddedicated power supplies.
pcDuino3Nano hasanHDMIconnectorthroughwhich you can transmit both video and audio in 1080p quality.
Specification and comparison
| Basic information | ||
 |
 |
|
| Model | Raspberry Pi 3 model B | pcDuino3 Nano |
| Edition | 3 - 2016 r. | 2016 r. |
| Technical specification | ||
| Core | Quad-Core ARM Cortex A53 | Dual-Core ARM Cortex-A7 |
| Operating systems |
Linux Raspbian Windows 10 loT |
Linux Android |
| Clocking | 1.2 GHz | 1 GHz |
| Memory RAM | 1 GB LPDDR2 @ 900 MHz | 1 GB DRAM |
| Memory | microSD card |
4 GB Flash memory microSD card |
| GPIO socket |
40-pin connector (2x20 pin) raster 2.54 mm |
Arduino connectors raster 2.54 mm |
| Power supply |
5.1 V / 2.5 A via microUSB |
5.0 V / 2 A via microUSB |
| Dimensions of the tiles | 85 x 56 x 17 mm | 95 x 55 x 18 mm |
| Interfaces | ||
| USB interface | 4x USB 2.0 - socket type A |
2x USB 2.0 - socket type A 1 x USB OTG microUSB |
| Network interface | 10/100 Mbps Ethernet port | 1 Gbps Ethernet port |
| WiFi interface | 802.11 b/g/n 150 Mbps | No |
| Bluetooth | Low Energy, BLE 4.1 | none |
| Camera | CSI socket | MIPI interface |
| Touchscreen display | DSI socket | No |
| Video | HDMI HD 1080px / 30 fps | HDMI HD 1080px / 30 fps |
| Communication | UART, SLEEPING, I2C, GPIO |
3.5 mm audio, UART, ADC, PWM, STUPID, I2C, SPI, SATA |
Useful links |
