GSM module - Although the transfer of information at distance accompanies man since ancient times, this use for this purpose the electricity (and soon electromagnetism) had its beginning less than two centuries ago. Today no one is surprised by the possibility of voice communication with another person, regardless of whether it is in the same building or on the other side of the globe. Thanks to modern GSM modules is also possible communication with the device controllers, telemetry systems or robots and flying cars. In this category you will find the GSM modules for installation on the target device, as all ready shieldy and Board compatible with Arduino and has an integrated GSM modules.
GSM modules
SIM868 GSM/GPRS/GNSS + Bluetooth - communication module for Raspberry Pi Pico - Waveshare 20268
SIM868 GSM/GPRS/GNSS + Bluetooth is a communication module for Raspberry Pi Pico. It supports a wide range of 2G frequency bands and communication protocols such as TCP /...LTE GPS HAT - LTE / GPRS / GPS SIM7600E-H - for Raspberry 4B/3B+/3B/2B/Zero - Waveshare 14952
Shield for Raspberry Pi that allows you to send text messages and create calls in the GSM network. It also has a GPS module. It supports LTE CAT4 up to 150 Mbps. It...Device Prototype Micromis Base V1 WiFi/Bluetooth/GSM - development board - ESP32
Micromis Base V1 is an innovative development board that communicates using WiFi, GSM and Bluetooth wireless networks. Equipped with an accelerometer, gyroscope and...- New
LTE GPS HAT - NB-IoT / LTE / GPRS / GPS SIM7000E - for Raspberry Pi 3B+/3B/2B/Zero - Waveshare 14865
Shield for Raspberry Pi that allows you to send text messages in the GSM network. It also has a GPS and LTE module. It communicates via serial interface UART (RX, TX) using the...A-II GSM Shield, GSM/GPRS/SMS/DTMF v.2.105 - for Arduino and Raspberry Pi + connector for Arduino
The new version of the module working with Arduino and Raspberry Pi that provides communication in GSM and GPRS. Based on Quectel M95, it allows for voice calls, sending SMS...PiTalk 2G HAT - Wireless Communication Module - for Raspberry Pi - SB Components SKU25978
PiTalk 2G HAT is a module supporting GSM/GPRS + GNSS wireless communication based on the SIM868 chip. It works at 850/900/1800/1900 MHz frequencies. The maximum...- Reduced price
- Promotion
iNode MCU GSM - Bluetooth/WiFi/GSM gateway - ESP32
The iNode MCU GSM device is based on the ESP32 chip and programmed in the microPython language. GSM MCU has no specific functionality, it can, for example, periodically send...- Reduced price
- Promotion
i-hatGSM3G and c-uGSM/d-u3G/h-nanoGSM for Raspberry Pi
The module facilitating the connection of Raspberry Pi with a radio module of c-uGSM and d-u3G or powering module of g-SPS.- On sale!
- Promotion
DFRobot Shield NB-IoT/LTE/GPRS/GPS SIM7000E v2.0 - Shield for Arduino
Shield for Arduino, which allows you to send text messages and create connections in the GSM network. It also has GPS and LTE. It communicates via serial interface UART (RX,...GSM LTE Module IoT-u-GSM shield v2.19 BC95G - for Arduino and Raspberry Pi - u.FL connector
The module supports GSM and LTE communication. It allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card, powering module for battery...- Reduced price
- Promotion
DFRobot - SIM7600CE-T 4G (LTE) - shield do Arduino
Shield for Arduino module which allows you to send text messages and create calls in the GSM network. It is also equipped with GPS and LTE module. It communicates via UART...j-328GSM3GLader for c-uGSM/d-u3G/h-nanoGSM and Arduino Micro
Module to facilitate connecting an Arduino Micro with the radio modules c-uGSM and d-u3G or powering module g-SPS.- On sale!
- Promotion
FONA 808 Shield - GSM and GPS module for Arduino - Adafruit 2636
The module is working with Arduino, which provides connectivity in GSM and GPRS. It allows for voice calls, sending SMS messages. It also has a GPS module. On the Board are:...- On sale!
A-II GSM Shield, GSM/GPRS/SMS/DTMF v.2.105 - for Arduino and Raspberry Pi
The new version of the module working with Arduino and Raspberry Pi that provides communication in GSM and GPRS. Based on Quectel M95, it allows for voice calls, sending SMS...B-GSMGNSS Shield v2.105 GSM/GPRS/SMS/DTMF + GPS + Bluetooth for Arduino and Raspberry Pi
Module cooperating with Arduino and Raspberry Pi, which enables communication in GSM and GPRS standard and also GPS + GLONASS and Bluetooth communication. Based on...- Reduced price
- Promotion
Module LTE/GSM - u-GSM shield v2.19 EG91E - for Arduino and Raspberry Pi - u.FL connector
The module allows communication in LTE / GSM standard allows you to make voice calls, send SMS messages. On the board there are: SIM card connector , charging module for Li-Pol...- Reduced price
- Promotion
PiTalk 4G HAT - Wireless Communication Module - for Raspberry Pi - SB Components SKU25985
The PiTalk 4G HAT communication module in the form of an overlay compatible with Raspberry Pi minicomputers is based on the Quectel EG25-G system, which enables wireless...- New
Power supply module from the DDRV network source - g-SPS 1.02 for c-uGSM and d-u3G
The powering module and voltage converter for modules of c-uGSM and d-u3G to use with the AC power supply. Input voltage ranges from 5 V to 16 V. The output voltage is 4 V with...DFRduino Leonardo + module GSM/GPRS/GPS SIM808 - compatible with Arduino
Board is a combination of Leonardo with SIM808 GSM, GPRS and GPS. It features ATmega32u4 microcontroller and it has 20 digital inputs/outputs, 7 PWM channels, 12 analog inputs,...f-audioOutputs - audio extender board for c-uGSM and h-nanoGSM shields
Extension that adds a 2 jack connectors to the c-uGSM module. It facilitates the connection of a microphone and headphones or speakers to the Jack 3,5 mm contact.B-GSMGNSS Shield v2.105 GSM/GPRS/SMS/DTMF GPS Bluetooth for Raspberry Pi + connectors for Arduino
Module cooperating with Arduino and Raspberry Pi, which enables communication in GSM and GPRS standard and also GPS + GLONASS and Bluetooth communication. Based on...Module xyz-mIOT 2.09 M95FA Quad Band GSM + HDC2010, DRV5032 - for Arduino and Raspberry Pi
A small module combining many capabilities to facilitate communication in IoT. It has among others a 4 range GSM module, a temperature and humidity sensor and a Hall effect...See also
The GSM modules, i.e. communication, SMS, HTTP and more
Produced today the GSM modules allow you to use almost all the advantages that brings with it the development of modern mobile communication networks. And although there are still many modules, support voice calls, at the present time, this feature is relatively less often used in devices that are not included in the segment of mobile phones for data transmission, control, measuring or test much more useful is the ability to send and receive SMS and incoming calls. In the latter case, the choices available are almost all major protocols and operating modes, including querying, HTTP, low-level connection TCP and UDP, also support transfer files to/from server FTP. Importantly, almost all the GSM modules support the AT command, that is easy to implement the Protocol text, which can be used to perform manual test of the module using any terminal emulation program that supports virtual serial ports (using a Converter USB-UART).
The GSM modules in all sizes
In our range we offer a wide range of GSM modules, in the form of small-scale models for wlutowania on the target device, as the finished plates equipped in the power supply circuit, antenna and all required connectors and configuration elements. In this first group were, for example, GSM/GPRS module Fibcom G510 Q50-00 is designed for surface mounting using a pin located on all four sides of the base size of 20, 2 season 22 series,2 mm. a Little more ready GSM module-GPRS-Bluetooth – h-v nanoGSM.1.08. On a small Board size 30x32 mm was (besides the module), and two antenna connector U. FL, the Power button, mini-usb socket, there are LEDs and slots for SIM card and the pads in wlutowania goldpin connectors 2.54 mm. As if that wasn't enough, on the same Board fit even microchip charge controller Li-polymer.
Lining GSM for Arduino and Raspberry Pi
If Your project is based on Arduino and you want to avoid wires between the GSM module and the base Board, You probably have to taste one of our overlays Arduino Shield that contains a GSM module installed on the Board designs are 100% hardware compatible with the Arduino. A good example is the DFRobot Shield GSM/LTE/GPRS/GPS tile not only offers fast digital communication through a cellular network, but also access to your current location (with GPS receiver). For Raspberry Pi we propose a similar module Waveshare LTE GPS HAT compatible in size with Raspberry Pi is Zero, as well as with all other modules of the series 3B+/3B and 2B.