- EOL
Attention! The sale of the product has been completed. Check others inthis category. |
Description
PineA64+ minicomputer with a powerful ARM CortexA53 quad-core 64-bit 1.2 GHzARM processor.The board has2 GB of DDR3 RAM,Ethernet Gigabitport,HDMI1.4 (4K)port, 2 xUSB 2.0, 40+34 GPIO,microSD card slot,3.5 mmminiJackandCSI and DSI connectors.Works with Debian, Ubuntu and Android systems. The device is compatible withRaspberry Pi caps.
The device has 2 USB 2.0 ports, HDMI, Ethernet port and many others.
What do I need to run a PineA64+ minicomputer?
- MicroSD memory card- the media on which theoperatingsystem will be installed.
- The power supply:
- 5 V / 2 Afor the minicomputer itself
- Enclosure - protects the minicomputer from external conditions
- HDMI cable - toconnect the device to a monitor
- Mouse and keyboard- to control and enter data into the device
- Connected internet - for software download
Operating system
PineA64+ works with many systems including Debian, Ubuntu and Android. The drive is a microSD card.
Installation of the system is very easy -check the manual! |
Communication
PineA64+ has basic communication interfaces that can be found in PC-class office computers. The user has it at his disposal:
- two USB 2.0 connectors,under which you can connect e.g. a mouse, a keyboard, a WiFi card or a flash drive. If it turns out that there are too few sockets, you can increase their number by usingan external USB HUB.
- Ethernet socket, i.e. the possibility of direct connection to the LAN.
- GPIO x 40 pin- general purpose outputs/inputs that can be used to operate LEDs, buttons, motor controllers. Among them there are pins supporting interfaces: I2C, SPI and UART. Compatible withRaspberry overlays
- GPIO x 34 pin- Euler connector
- microSD slot- a slot for a microSD memory card on which the operating system can be installed.
PineA64+ has a slot formicroSD memory card. The card is not included in the set it can be purchased separately.
Power supply .
As a power source, the system uses a microUSB connector or a 3.7V lipol battery through the appropriate connector. The manufacturer recommends that the voltage given on the connector should be 5.0 V, while the current capacity of the power supply used should be at least 2.0 A. In our offer you will finddedicated power supplies.
PineA64+hasanHDMIconnector, throughwhich you can transmit both video and audio in 4K quality.
Specification and comparison
Basic information | ||
Model | Raspberry Pi 3 model B | PineA64+ |
Edition | 3 - 2016 r. | 2016 r. |
Technical specification | ||
Core | Quad-Core ARM Cortex A53 | Quad-Core ARM Cortex-A54 |
Operating systems |
Linux Raspbian Windows 10 loT |
Debian Ubuntu Android etc. |
Clocking | 1.2 GHz | 1.2 GHz |
Memory RAM | 1 GB LPDDR2 @ 900 MHz | 2 GB DDR3 |
Memory | microSD card | microSD card |
GPIO socket |
40-pin connector (2x20 pin) raster 2.54 mm |
40-pin connector (2x20 pin) raster 2.54 mm 34-pin connector (2x17 pin) 2.54 mm raster (Euler) |
Power supply |
5.1 V / 2.5 A via microUSB |
5.0 V / 2 A via microUSB 3.7 V through lipol connector |
Dimensions of the tiles | 85 x 56 x 17 mm | 127 x 79 x 16 mm |
Interfaces | ||
USB interface | 4x USB 2.0 - socket type A |
2x USB 2.0 - socket type A |
Network interface | 10/100 Mbps Ethernet port | 10/100/1000 Mbps Ethernet port |
WiFi interface | 802.11 b/g/n 150 Mbps | none, dedicated connector |
Bluetooth | Low Energy, BLE 4.1 | none, dedicated connector |
Camera | CSI socket | CSI socket |
Touchscreen display | DSI socket | DSI socket |
Video | HDMI HD 1080px / 30 fps | 4K (3820 x 2160 px) |
Communication | UART, SLEEPING, I2C, GPIO |
UART, SPI, I2C, GPIO, IR, I2S S/PDFI |
Additional |
RTC clock lipol charging module |
Starting sets
We also offer sets with Pine64+ minicomputer:
- PineA64+ Online Kitwith housing, power supply, WiFi module, memory card and keyboard
- PineA64+ Kit+with enclosure, power supply, WiFi module, memory card
ThePineA64+ Online Kitincludes a minicomputer, power supply, enclosure, memory card and WiFi module.
Useful links |