- EOL
|
Attention! The product has been discontinued. Check other products in category. |
Description of Odroid XU4 - Samsung Exynos5422 Octa-Core 2,0GHz / 1,4GHz + 2GB RAM
Minicomputer Odroid version C0 with a powerful processorSamsung Exynos5422 octa-corewith coresCortex-A15 2.0 GHz quad-core + Cortex-A7 with a clock frequency of 1.4 GHz quad-core. Board has2 GB of RAM LPDDR3, built-in Gigabit Ethernet port, HDMI 2.0 port and three USB slots including 2x USB 3.0, 30 GPIO, connectors for memory cards microSD and the IR receiver. Works with Ubuntu 15.04 or Android 4.2.2.
The device has 3 USB slots, HDMI connector and an Ethernet port, and many others.
What it takes to run minicomputer Odroid?
- The microSD card or eMMC memory - carrier, on which will be installed operating system
- AC adapter:
- Housing- protects minicomputer from the influence of external conditions
- HDMI cable- to connect the device to the monitor
- Mouse and keyboard - to control and input data into the device
In our store arre also availableoptional accessories- in type of adapter wi-fi,touchscreen display orthe module USB 3.0 - SATA
Operating system
Odroid C0 works with Ubuntu 15.04 and Android 4.2.2 based on kernel 3.10 LTS. The drive of device, can be a microSD card or a Flash memory eMMC 5.0 HS400.
|
Systems Ubuntu and Android can be downloaded fromthe manufacturer's website. The installation is very simple -check out our manual! |
Mounted radiator with fan is included.
Communication
Odroid has the main communication interfaces, which can be found in office computers of PC class. In addition to the previously listed connectors for audio and video, the user has at his or her disposal:
- HDMI port - transfers the image on the monitor
- USB connectors, to which you can connect, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB. This version has 2 USB 3.0 and 1x USB 2.0
- GPIO x 30pin + 12pin 2mm raster- outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers, engines. Among them are the pins, supportting interfaces: I2C, SPI and UART. You musr purchase goldpin straps separately and solder them yourself.
- a slot for microSD - slot formemory cards microSD, on which can be installed the operating system.
Odroid has a microSD slot on the top side of tile. Card is not included and can be purchased separately.
|
Connectors GPIO Odroid XU4 Board have a non-standard I/O raster of 2 mm. |
Power
As a power source, the system uses theDC connector 5.5 x 2.1 mm. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 and a minimum output current of the used power supply shall be not less than 4.0 A. You will finda specialpower supply in our assortment.
Cases
In our assortment you will findspecial housings that protects minikcomputer Odroid from external conditions. Special power supplies also available.
Photo of minicomputer Odroid ina special housing.
Specifications and comparison
| Basic information | ||||
 |
 |
 |
 |
|
| Model | Odroid C0 | Odroid C1+ | Odroid C2 | Odroid XU4 |
| Specification |
||||
| Processor | Amlogic S805 | Amlogic S805 | Amlogic S905 | Samsung Exynos5422 |
| The core |
Quad-Core 32-bit ARM Cortex A5 |
Quad-Core 32-bit ARM Cortex A5 |
Quad-Core 64-bit ARM Cortex-A53 |
Octa-Core ARM Cortex-A15 ARM Cortex™-A7 |
| Graphics |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
3D Mali-T628 MP6 OpenGL ES 3.0/2.0/1.1 |
| Systems |
Ubuntu 14.04 Android 4.4 Kernel 3.10 LTS |
Ubuntu 14.04 Android 4.4 Kernel 3.10 LTS |
Ubuntu 16.04 Android 5.1 Kernel 3.14 LTS |
Ubuntu 15.04 Android 4.4.2 Kernel 3.10 LTS |
| Clock frequency | 1.5 GHz | 1.5 GHz | 1.5 GHz | 2 GHz / 1.4 GHz |
| Architecture | ARMv7 | ARMv7 | ARMv8 | ARMv7-A |
| RAM |
1 GB DDR3 SDRAM |
1 GB DDR3 SDRAM 792MHz |
2 GB DDR3 SDRAM 792Mhz |
2 GB LPDDR3 RAM 750Mhz |
| Memory |
microSD memory card UHS1 eMMC4.5 HS200 |
microSD memory card UHS1 up to 16 GB eMMC4.5 |
microSD memory card UHS1 with capacity up to 128 GB eMMC5.0 |
microSD memory card The UHS1 up to 64 GB eMMC5.0 |
| GPIO slot |
Connector 40-pin + 7-pin I2S (to solder) |
Connector 40-pin + 7-pin I2S |
Connector 40-pin + 7-pin I2S |
Connector 30-pin + 12 pin I2S raster 2mm |
| Power |
5 V / 2 A DC Jack |
5 V / 2 A DC Jack |
5 V / 2 A DC Jack |
5 V / 4 A DC 2,5x2,1mm |
| Tile sizes | 58x56x11mm | 85x56x18mm | 85x56x18mm | 82x58x22mm |
| Interfaces | ||||
| USB-Host |
2 x USB 2.0 (optional soldering) |
4x USB 2.0 slot type a |
4x USB 2.0 slot type a |
2x USB 3.0 1x USB 2.0 slot type a |
| USB OTG | - |
1x microUSB |
1x microUSB | - |
| Network interface | - |
Ethernet 10/100/1000 Mbit/s |
Ethernet 10/100/1000 Mbit/s |
Ethernet 10/100/1000 Mbit/s |
| The RTC system | Built-in | Built-in | - | - |
| Video | HDMI | HDMI | HDMI 2.0 4K/60 Hz | HDMI 1.4 a |
| Audio |
HDMI / I2S |
HDMi |
HDMI / I2S |
HDMI |
| ADC |
2 channels 10-bits |
2 channels 10-bits |
2 channels 10-bits |
2 channels 10-bits |
| Communication |
UART, SPI, I2C, GPIO, ADC |
UART, SPI, I2C, GPIO, ADC |
UART, SPI, I2C, GPIO, ADC |
UART, SPI, I2C, GPIO, ADC |
Video
Introducing the minicomputer Odroid XU4
