• EOL

ATWINC1500 - module WiFi SPI/UART + PCB antenna - Adafruit 2999

Index: ADA-05412 EAN: 5904422354336

Wi-fi module from Atmel operating in the 802.11 bgn standard. The device works with the voltage from 3.3 V to 5.5 V, it communicates via the SPI interface. It has support for SSL, WEP, WPA, WPA2 and AP mode, which allows you to create ad-hoc network. The module also works with TLS 1.2 security with 19.4.4 firmware. It has a built-in PCB antenna.

ATWINC1500 - module WiFi SPI/UART + PCB antenna - Adafruit 2999
€36.00
€29.27 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Adafruit
Compatibility: Arduino

Attention!

The product has been discontinued. Check other products in category.

Description

Wi-fi module from Atmel operating in the 802.11 bgn standard. The device works with the voltage from 3.3 V to 5.5 V, it communicates via the SPI interface. It has support for SSL, WEP, WPA, WPA2 and AP mode, which allows you to create ad-hoc network. The module also works with TLS 1.2 security with 19.4.4 firmware.

Key features

  • Module from ATmel ATWINC1500 (documentation) working in wi-fi 802.11 bgn standard
  • It has a support for AP mode (Access Point) that allows you to create ad-hoc network
  • Works with a voltage of 3.3 V and 5.0 V
  • It communicates
  • Supports SSL, WEP, WPA, WPA2, and TLS 1.2 securities with 19.4.4 firmware.
  • Built-in antenna as PCB tracks

 

 

 

 

The product is compatible with Arduino

On the Adafruit website, you can findthe user manualalong witha libraryfor Arduino.

The library provided by the manufacturer is working correctly with the Arduino Zero. There's no certainity if this will work with other Arduino modules.

 

Pins

This set includes the goldpin connectors - 2.54 mm pitch for self-soldering. Description of the pins is in the table.

 

ATWINC1500 - moduł WiFi dla Arduino

 

Pin Description
VIN DC supply voltage of 3.3 V or 5 V.
GND The ground of the system.
CCS Clock line of the SPI bus - it works with a voltage of 3.3 V and 5 V.
MISO

The data line of the SPI bus - it works with a voltage of 3.3 V.

MOSI The data line of the SPI bus - it works with a voltage of 3.3 V and 5 V.
CS Chip Select. By default in the high status, during the transfer, you must indicate the low status.
EN Indicating the high status from 3.3 V to 5 V, enables the module. Indicating the low status disables the system. By default, it is pulled to GND with a resistor of 100 k (module off)
IRQ External interrupts. Check the documentation for details.
RST

The Reset Pin is activated with the high status.

WAKE

Signal causing the operation of the sensor.

CFG

The choice between the SPI interface (by default) and UART interface.

RXD

Receiver of the UART interface.

TXD

Transmitter of the UART interface.

Specification

  • Supply voltage: from 3.3 V to 5.5 V
  • The wi-fi ATWINC1500 module
  • Support for AP mode
  • Support for WEP, WPA, WPA2 and SSL securities
  • Support for TLS 1.2 with firmware 19.4.4
  • Communication: SPI and UART interface
  • Built-in PCB antenna
  • Dimensions: 33 x 28 x 48 mm
  • Weight: approx 5 g

 

UC - Microcontroller ATWINC1500
Package width 7 cm
Package height 0.7 cm
Package depth 5 cm
Package weight 0.006 kg

Be the first to ask a question about this product!

Product reviews

ATWINC1500 - module WiFi SPI/UART + PCB antenna - Adafruit 2999

5/5

Average grade

1

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: