• EOL

JRK G2 18v27 - single channel USB driver with 30V / 27A feedback - Pololu 3148

Index: PLL-12122 EAN: 5904422318703

Extremely easy to use motor controller with feedback support. Available communication interfaces: USB, TTL, I2C, analog and radio. Supply voltage is from 6.5 V to 30 V and continuous current up to 27 A.

JRK G2 18v27 - single channel USB driver with 30V / 27A feedback - Pololu 3148
€123.90
€100.73 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Attention!

The product has been discontinued. Check other products in category.

Product description: JRK G2 18v27 - single channel USB motor controller with 30 V / 27 A feedback - Pololu 3148

Extremely simplemotor controllerwith feedback supportbelonging to the second generation of JRK controllers - JRK G2. Provides easy speed or position control (but not for both simultaneously). Available communication interfaces: USB, TTL, I2C, analog and radio. Supply voltage isfrom 6.5 V to 30 Vand continuous currentup to 27 A.

Technical specification of the controller

  • Supply voltage for motors: from 6.5 V to 30 V
  • Continuous current per channel: 27 A
  • Maximum PWM signal frequency: 20 kHz
  • Number of channels: 1
  • Connector: microUSB
  • Interfaces: USB, serial TTL, I2C, RC servo, analog voltage
  • Protection against reverse connection of power supply
  • Dimensions (without connectors): 43 x30x 11 mm
  • Weight (without connectors): 10 g

The kit requires simple soldering of basic electronic components.


Special features

  • Easy open or closed loop control of one DC motor
  • 5 control interfaces
    • USB: direct connection to the computer
    • Serial TTL: works with 5 V, for connection to a microcontroller
    • I2C: for connection to microcontroller
    • Radio signalfor connection to RC system
    • Analog voltagefor use with a potentiometer or pad
  • Feedback options
    • Analog voltage; 0 V to 5 V - for closed loop system
    • Frequency:for speed control using pulse counting
    • None: for open loop
    • (the controller does not support quadrature encoders)
  • 20 kHz ultrasonic PWM - silent operation (5 kHz can also be set)
  • Simple control and calibration using dedicated software
  • Configurable:
    • PID coefficients
    • Maximum current
    • Maximum PWM signal filling
    • Maximum acceleration and deceleration
    • Fault response
    • Input calibration for analogue and RC control
  • CRC error detection
  • Reverse polarity protection
  • Firmware upgradeable

Controller pinouts

Pololu Jrk G2 18v27

Comparison of the JRK with the new generation - JRK G2

The new G2 family has many improvements compared to the older JRKs. The JRK G2 drivers support higher operating voltages and higher currents, yet are smaller than their predecessors. Other features:

  • Hardware current limiting - the controller limits the motor current if it exceeds a set threshold
  • More accurate speed control at low frequencies
  • I2C interface for increased controllability
  • Possibility to measure VIN voltage to monitor power supply or batteries
  • MicroUSB connector instead of miniUSB
  • Speed reduction limitation (JRK first version had only acceleration limitation)
  • PID coefficients can be changed live via UART, I2C or USB

The JRK G2 controllers are software compatible with the older version, so there is no need to replace the control application.

Voltage to 6.5 V
Voltage from 30.0 V
Current 27 A
Channels 1
Package width 11 cm
Package height 2 cm
Package depth 11 cm
Package weight 0.011 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: