• EOL

Resin for 3D printer FormFutura Platinum SLA Series 0,5kg - Solid Granite Black

Index: FFU-18255 EAN: 8719956553110
A photopolymer resin in a solid black color. Used in open source 3D printers, compatible with SLA, DLP and LCD technologies. The resin is cured by a light wavelength ranging from 385 nm to 405 nm. It gives off a slightly unpleasant but non-intrusive odour when the print is formed. The finished models have a high level of detail and a smooth surface. Package contains 0,5 kg of product.
Resin for 3D printer FormFutura Platinum SLA Series 0,5kg - Solid Granite Black
€57.90
€47.07 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: FormFutura

Attention!

The product has been discontinued. Check other products in category.

Product description: Resin for 3D Printer FormFutura Platinum SLA Series 0,5 kg - Solid Granite Black

Solidblackphotopolymer resin. Used in open source3D printers, compatible with SLA, DLP and LCD technologies. Theresinis cured by a light wave of the length ranging from385 nm to 405 nm. It gives off a slightly unpleasant but non-intrusive odour when the print is formed. The finished models have a high level of detail and a smooth surface. Package contains0.5 kg of the product.

Żywica FormFutura Platinum SLA Series

FormFutura Platinum SLA Series Resin.


Modele wykonane z użyciem żywicy FormFutura

Models made of FormFutura Platinum SLA Series resin.

Main features of the Platinum SLA Series resin

  • Enable high resolution 3D printing. Provide very high detail of the model.
  • Emitted during the printing unpleasant smell is not intense.
  • Platinum SLA resins have high dimensional accuracy and low shrinkage
  • They show low water absorption
  • Platinum SLA Series resins are compatible with open source 3D printers that use light in the wavelength range of 385 nm to 405 nm to cure the print material.
  • Main applications of Platinum SLA Series resins: figure printing, functional prototyping

Steps to be taken before printing

  • Before each use, shake the bottle for at least 2 minutes.
  • Then leave the resin for about 10 minutes to let the air bubbles escape from the resin
  • After printing, unused resin can be transferred from the printer tank to the bottle

Always wear protective equipment when handling the resin:gogglesand nitrile gloves.

Final processing of the finished 3D printout

  • Ready model should be rinsed in isopropyl alcohol (IPA) or bioethanol for about 5 minutes.
  • The manufacturer recommends the use of ultrasonic cleaner.
  • Before further curing check if the model is completely dry after rinsing
  • Place the rinsed parts in a well-ventilated room for at least 30 min. (Compressed air can also be used for at least 2 minutes).
  • Cure the objects in a special chamber for 20 to 30 minutes at 65°C
  • Recommended curing wavelength is from 300 nm to 410 nm
  • During the grinding of resin it is absolutely necessary to remember about protection of airways
Żywica Engineering Series Tough


The packaging of Platinum SLA Series resins protects them from drying.

Please note that the printing method may vary depending on the printer used, its movement geometry, settings and the method of curing the model.

Specification of Platinum SLA Series resin

  • Viscosity: 700 cps at 25°C
  • Density: 1.12 g/cm2

The table contains mechanical parameters of cured resin. Tested objects were cured for 30 minutes using high power LEDs.

Parameter Value Test method
Glass transition temperature (Tg) 54°C ASTM D7028
Water absorption 0,3% ASTM D570-98
Impact strength (IZOD) 15 J/m ASTM D256A
Tensile Strength 62 MPa ASTM D638M
Tensile Resilience 2200 MPa ASTM D638M
Elongation at tension 4% ASTM D638M
Bending Strength 75 MPa ASTM D790M
Elasticity 1900 MPa ASTM D2240
Shore Hardness 78 ASTM D2240
Colour black
Mass 500 g

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: