• EOL

Step-Down Voltage Regulator D24V3AHV - 4V - 25V 0,3A - Pololu 2102

Index: PLL-00661

A small step-down converter module. Input voltage 4.5 V to 42 V. Adjustable output voltage in the range: 4 V - 25 V. Maximum output current 300 mA.

Step-Down Voltage Regulator D24V3AHV - 4V - 25V 0,3A - Pololu 2102
€6.71
€5.45 tax excl.
Manufacturer: Pololu

Attention!

The product has been discontinued. Check other products in category.

Product description: Pololu D24V3AHV - step-down converter 4 V - 25 V 0.3 A

  • Dimensions: 23 x 17 x 5 mm
  • Cable length:
  • Motor cables: 55 mm
  • Wires for package: 75 mm
  • Cable to receiver: 95 mm
  • Weight (with wires): 8 g
  • Operational current: continuous 10A / 10 min
  • Max. operational current (peak): 15A
  • Plug for receiver: JR type
  • Number of cells: 2 - 3 LiPo
  • Operating voltage: 7.4 - 11.1V
  • Built-in functions: brake programming, timing

Leads of Pololu D24V3AHV - step-down converter 4 V - 25 V 0.3 A

The module has four pins:

  • VIN- input voltage,
  • GND- ground potential,
  • VOUT- output voltage,
  • SHDN- disabling the system.

If a low state appears on theSHDNpin (below 0.3 V), the converter will be turned off and the current consumption will not exceed 20 uA. Entering a high state (above 2.3 V) reactivates the system. The output can be permanently connected to the VIN or left unconnected if the switch-off mode will not be used.

The connectors are properly labeled on the board. The pitch of the pins is 2.54 mm (popular goldpin connectors). The module can be plugged intothe breadboard, connected withwiresor soldered into a dedicated PCB.

The output voltage is set with a potentiometer. Setting a voltage higher than the input voltage will not damage the system. However, there will be large oscillations. So it is recommended not to set the voltage higher than the input voltage.

Pololu D24V3AHV 

Output voltage oscillogram. VIN is 5V. VOUT set above 5V.

Selecting the output voltage

Turning the potentiometer clockwise increases the output voltage.

Efficiency and output current

Efficiency is defined as the ratio of the output power to the input power (Power out) / (Power in). This is a very important parameter when working with portable energy sources (batteries and accumulators), where the working time per one charging cycle is important. The dependence of the efficiency on the input voltage is shown in the graphs below.

The output values of the Pololu D24V3AHV converter

Graph showing the relationship between the output voltage and the position of the potentiometer for 4-25V and 2.5-7.5V converters.

Pololu D24V3AHV

Pololu D24V3AHV - step-down converter

Polol converter D24V3AHV

Step-down converter 4V-25V Poolu

Dangerous voltage pulses

When connecting the power supply to the module, dangerous, short electric pulses of large amplitude (so-called pins) may appear, which may permanently damage the system. Pololu tests show that for voltages above 20V, the pins can have an amplitude exceeding 42V. In order to protect against this undesirable phenomenon, it is recommended to solder a capacitor with a value of at least 33uF as close to the converter's power pins as possible.

Specification of the step-down converter 4 V - 25 V 0.3 A - Pololu D24V3AHV

  • Input voltage: 4.5 V to 42 V
  • Adjustable output voltage: from 4 V to 25 V
  • Maximum output current: 300 mA
  • Switching frequency 500 kHz
  • Built-in protection (switch) to protect against too high power consumption and too high temperature
  • Dimensions: 15.3 x 10.2 x 4 mm
  • Weight: 1g (without connectors)
Length 15 mm
Width 10 mm
Height 4 mm
Voltage to 4.5 V
Voltage from 42 V
Voltage output from 4.0 V
Output voltage to 25 V
Current 0.3 A
Stabilizer - Type2 switching
Stabilizer - Type step-down

Same-day shipping

  • Crediting the payment for the order on our account on a business day before 10:00 AM means sending the goods on the same day.
  • All packages are being delivered by GLS Group courier and covered with insurance up to 1200 EUR.
  • You will receive a link to track your package and monitor the progress of delivery as soon as it is shipped.

Terms of delivery 

GLS - zone 1

Austria, Belgium, Croatia, The Czech Republic, Denmark, Germany, Netherlands, Poland, Slovakia 

  • Delivery time: 2-4 days
  • Delivery cost: from 4.18 EUR
  • Insurance: 1200 EUR
GLS - zone 2

Bulgaria, Estonia, France, Hungary, Italy, Latvia, Lithuania, Luxembourg, Portugal, Romania, San Marino, Slovenia

  • Delivery time: 2-5 days
  • Delivery cost: from 5.35 EUR
  • Insurance: 1200 EUR
GLS - zone 3

Finland, Greece, Ireland, Spain, Sweden 

  • Delivery time: 2-7 days
  • Delivery cost: from 7.67 EUR
  • Insurance: 1200 EUR

Payment methods

Card image cap
PayPal
  • Botland is a PayPal verified seller. Protect your financial information with this fast, safe and secure online payment system.

Card image cap
PayU
  • Choose easy and quick PayU e-payment method. Your financial information will stay secure.

You might also like

AVR microcontroller - ATmega8A-AU SMD

Atmel microcontroller AVR with 32-led case soldered on surface - SMD. Voltage supply range from 2.7 V to 5.5 V, frequency up to 16 MHz, has 8 KB Flash, 1 KB RAM, 512 bytes of...
Index: UCC-00079
Index: UCC-00079
Available
Check quantity
Regular price €6.49 Price €6.49

AVR microcontroller - ATmega128A-AU SMD

Popular microcontroller ATmega128a-AU from ATmel AVR family in a case soldered on surface (SMD).
Index: UCC-00156
Index: UCC-00156
Delivery scheduled for 2022-10-05
Regular price €15.17 Price €15.17

Microcontroller ST STM32F103RBT6 Cortex M3 - LQFP64

32-bit microcontroller ST in LQFP48  case with ARM core Cortex-M3 is equipped with: 128 kB Flash, 20 KB RAM, CAN, UART, I2C, SPI, ADC.  P hotos of this product  are...
Index: UCC-00508
Index: UCC-00508
Unavailable
Regular price €7.36 Price €7.36
  • EOL

Customers who bought this product also bought:

Products from the same category: