Electric motors, to connect them with the control system – for example, the programmable control unit PLC or industrial PC jednopłytkowym such as the Raspberry Pi require a motor driver. The modules are available in our store a wide variety of settings, in versions with two or even szesnastoma control channels. Some two-channel motor driver DC, can also be used, e.g. for control of stepper motors, although this requires the implementation of control algorithm in the module monitor the operation of the driver.
Motor drivers modules
DRV8835 - two-channel motor controller 11V / 1,2A - Pololu 2135
Two-channel driver for DC motors. Continuous current per channel 1.2 A (temporary up to 1.5 A). Power supply from 2.0 to 11 V.Cytron MD13S - single-channel 30V / 13A motor controller
Single channel DC motor controller. Continuous current per channel 13 A (momentary 30 A ). Supply voltage from 5 V to 30 V. There is a Grove connector on the board.Cytron MD10C - single-channel 30V / 13A motor controller
Single channel DC motor controller. Continuous current per channel 13 A (momentary 30 A). Supply voltage from 5 V to 30 V .Cytron Maker Drive MX1508 - two-channel motor controller 9.5V/1A
Simple to use, two-channel DC motor driver with H-bridge. 1 A continuous current per channel (1.5 A momentary). Power supply from 2.5 V to 9.5 V. Output current at 5 V is 0.2 A.Cytron MDD3A - dual-channel 16V / 3A motor controller
The Cytron MDD3A motor controller has the ability to control 2 DC motors or 1 stepper motor. Continuous current per channel is 3 A (momentary 5 A). Supply voltage is from 4 V...Cytron MD20A - single-channel motor controller 30V/20A
Single-channel DC motor controller based on MOSFET transistors. Enables control of motor speed through PWM channel. Continuous current per channel is 20 A (momentary 60 A)....Simple DC 28V/3A motor driver - module with knob
Extremely easy to use, single-channel direct current motor controller with speed control knob. The device works on the basis of PWM signal. Power supply voltage is from 8 V to...L298N Dual H Bridge DC StepperMotor Driver Board - Iduino ST1112
L298N dual channel DC motor controller module. It is powered from 5 V to 46 V. The maximum channel current is 2 A. The chip has a built-in 5 V voltage regulator to supply the...Cytron MD10-POT - DC motors controller 30V / 10A + switch + potentiometer
Single channel DC motor controller allowing motor control by switch and potentiometer without the need for microcontroller and programming. Continuous current per channel 10 A...TB6612FNG - two-channel motor controller 13.5V / 1A - Pololu 713
Pololu module with dual channel DC motor driver. It is powered from 4.5 V to 13.5 V. The continuous current per channel is 1 A, when both channels are connected the value...Motor regulator DC 12-40V/10A/400W - with a speed control knob
A simple controller with an integrated rotary potentiometer to control the speed of a DC motor up to 400 W. Powered from 12 V to 40 V.Cytron MDD10A - dual-channel 30V / 10A motor controller
Two-channel DC motor controller. Continuous current per channel is 10 A (momentary 30 A) . Supply voltage is 5 V to 30 V . The controller works with logical voltage 3.3 V...L298N - two-channel motor controller - 12V/2A
Module with dual-channel driver for DC motors L298. It is supplied with the voltage up to 12 V. Maximum current per channel is 2 A. The system has embedded voltage regulator 5...Cytron Shield-MDD10 - two-channel DC motor driver - 7V-30V/10A - Shield for Arduino
A module that allows you to control two DC motors or one stepper motor using Arduino. The overlay allows you to adjust the direction and speed of motors with current...DFRobot HR8833 - two-channel driver for DC 10V/1,5A motors
A miniature, two-channel DC motor controller. The device operates on the basis of PWM signal. The motor supply voltage is from 3.3 V to 10 V, maximum current is 1.5 A.MAX14870 - single-channel motor controller 36V/1.7A - Pololu 2961
Single-channel DC motor controller. Continuous current per channel 1.7 A (momentary to 2.5 A). Supply voltage from 4.5 V to 36 V.DFRobot L298N - two-channel motor controller - 12V / 2A
Two-channel DC motor controller based on L298N system. Supply voltage is up to 12 V. Maximum current per channel is 2 A. The system has a built-in voltage regulator 5 V, to...Dual channel DC motor driver, I2C interface - HAT for Raspberry Pi - Waveshare 15364
HAT shield for Raspberry Pi 3 / 2 / B+ / Zero / Zero W enabling the control of two DC motors using the I2C interface. It can control simultaneously the two DC motors. A maximum...DFRobot - motor driver 5,5V/1,5A for BBC micro:bit
An overlay for micro:bit to control four DC motors , two stepper motors and eight servos (5.5V/1.5A). Additionally the module has 9 I/O pins Micro:bit.Cytron MD10 - 1-channel motor driver 30V/10A - Shield for Arduino
Shield for Arduino with single-channel driver for DC motors operating with a voltage from 7 V to 30 V and current up to 10 A (short term 15 A). It has NMOS H-Bridge. The board...TB6612 Motor Shield - 4x DC motor driver - 12V/1,2 A - Shield for Arduino
The module allows you to control four DC motors (DC), with two stepper motors or two servos using Arduino kits. The system allows you to adjust the direction and speed of...DRV8874 - single channel 37V/2.1A motor driver - Pololu 4035
Single-channel DC motor driver from Pololu equipped with the DRV8874 system. It is supplied with the voltage from 4.5 V to 37 V. The continuous current per channel is 2.1...Cytron SmartDriveDuo MDDS10 - two-channel 35V / 10A motor controller
Two-channel intelligent DC motor controller . Continuous current per channel 10 A (momentary 30 A). Supply voltage from 7 V to 35 V. It has interfaces such as UART, PWM,...DC Motor Driver HAT V1.0 - 2-channels motor driver 12V/1,2A - HAT for Raspberry Pi - DFRobot DFR0592
Two-channel DC motor controller TB6612FNG operating with voltage from 7 V to 12 V and continuous current 1.2 A per channel and momentary 2 A. The module in the form of an...See also
Integrated modules for motor control
Motor drivers modules are very popular in electronics, in particular to the design of prototype devices and for fans. Thanks to an integrated design module contains all the necessary circuits and discrete elements on a small printed circuit Board. Due to this the controller for this connection, only need a power source, the engine and, of course, control signals, for example, a computer or a microcontroller. Integrated motor drivers can be implemented in various designs such as compact robots or machines with small numbers.
A wide range of modules for motor control
The motors are typical a number of options under which you need to find motor drivers modules. In addition to intuitively understand the number of channels also have other settings, of which the most important is the voltage and operating current. Voltage range of work suggests that can be the rated voltage of the motors controlled by this module. Operating current specyfikuje the maximum allowable current supported by this driver, so it is important that the current consumption of this engine was no more than this value. Excess of maximum permissible parameters of the driver can fail the entire system.
Multi-channel drivers for use with minikomputerami
The assortment of our shop you can find motor drivers – multi-channel modules equipped with a dedicated interface for connection to PC jednopłytkowych such as a popular series of Raspberry Pi or Micro:bit for tile prototypes in the form shielda in the format of Arduino. Due to the fact that these modules can be connected to a wide range of minicomputers to focus on the fact that the format of the Arduino, as well as 40-pin connector of the Raspberry Pi, it's widely accepted in this sector, standards of signal receiving modules for developers.