• EOL

Step-Up/Step-Down Voltage Regulator S10V3F9 - 9V 0,3A - Pololu 2095

Index: PLL-01843 EAN: 5904422305703

Step-up/step-down converter with 9 V output voltage. Maximum current 300 mA. Power supply 2.5 V - 18 V.

Step-Up/Step-Down Voltage Regulator S10V3F9 - 9V 0,3A - Pololu 2095
€10.90
€8.86 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Pololu

Attention!

The product has been discontinued. Check other products in category.

Product description: S10V3F9 - 9V 0.3A step-up/step-down 9V - Polyol 2095.

Step-up/step-down converter with 9 V output voltage. Maximum current 300 mA. Power supply 2.5 V - 18 V.

Main features

  1. The output voltage can be higher, lower or equal to the supply voltage (between 2.5 V and 18 V).

  2. Continuous output current is maximum 300 mA - depends on the input voltage (seefurther details).

  3. Output voltage 9 V with 4 % accuracy.

  4. Integrated temperature protection system.

  5. Small dimensions: 14.6 x 10.16 x 2.54 mm.

The large input voltage range and the stability of the 9 V output voltage with an accuracy of 4 % make the module very well suited as a stabiliser for battery-powered systems. For example, when 9 V is required in a system powered by seven NiMh batteries that are fully charged to 11 V, 8.4 V nominal and only 7.4 V discharged.

In a typical application, the system can provide current up to 300 mA (seefurther details).The controller is equipped with temperature protection, but has no protection against short circuit and reverse power connection.

Outputs

The module has four outputs:

  • VIN- input voltage from 2.5 V - 18 V. If the lower module does not switch on, the higher one can damage the system.
  • GND- ground potential.
  • VOUT- output voltage 9 V.
  • SHDN- switching off the system - giving a low state, makes the system go into a low power consumption state. The output is pulled to the VIN via a 10 kΩ resistor, which makes the system switched on by default.

Connectors are properly signed on the board. Outputs Raster is 2.54 mm (popular goldpin connectors). The module can be plugged intoa contact board, connected withwires or solderedinto a dedicated PCB.

System efficiency

Efficiency is defined as the ratio of input power to output power (Pout/Pin). This parameter is particularly important for battery operation when it is important to keep the system running as long as possible on a single charge. The efficiency of the inverter depends on the flowing current and the input voltage (graph below). On average, it is 70-80 %, which allows the maximum use of battery power.

Przetwornica S10V3F9 - sprawność układu w zależności od pobieranego prądu

Przetwornica S10V3F9 - sprawność układu w zależności od napięcia wejściowego

Output current

The maximum current that the system can deliverdependson: input voltage and operating temperature. The dependence of the maximum current consumption on the input voltage is shown in the figure below. If the operating temperature reaches too high a value, the module will automatically disconnect the power supply.

Przetwornica S10V3F9 - prąd wyjściowy

Voltage jumps (pins)

In electronic circuits the starting current may cause the occurrence of so-called pins, i.e. sudden voltage surges to a value above a set level. If the amplitude of the pins exceeds the permissible value of the regulator, it can be destroyed. Therefore, if the circuit will be supplied with voltage above 11 V or the load will have high inductance, we recommend to solder a capacitor of 33 uF / 25 V or higher as close as possible to the circuit between VIN and GND.

S10V3F9 inverter specification

  • Input voltage: 2.5 V to 18 V
  • Output voltage: 9 V
  • Frequency of operation: 1.5 MHz
  • Maximum output current: 300 mA
  • System current consumption (quiescent current): 2 mA
  • Small dimensions: 14.6 x 10.16 x 2.54 mm
  • Weight (without connectors): 0.6 g

Length 15 mm
Width 10 mm
Height 3 mm
Voltage to 2.5 V
Voltage from 18.0 V
Voltage output from 9.0 V
Output voltage to 9 V
Nominal output voltage 9 V
Current 0.3 A
Stabilizer - Type2 switching
Stabilizer - Type step-up/down
Package width 7.5 cm
Package height 8.5 cm
Package depth 0.2 cm
Package weight 0.002 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: