• EOL

UART GPS NEO-7M-C (B)

Index: WSR-06814

Module GPS / GLONASS NEO-7M-C on board with installed connectors goldpin. Used, supports 56 channels, works with a voltage from 3.3 V to 5.5 V, it communicates via interface UART (TX, RX) and the refresh frequency is up to 5 Hz. The module is equipped with straight goldpins.

UART GPS NEO-7M-C (B)
€17.50
€14.23 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: OEM

Attention!

The product has been discontinued. Check others products incategory.

Description

Module GPS / GLONASS NEO-7M-C on board with installed connectors goldpin. Used, supports 56 channels, works with a voltage from 3.3 V to 5.5 V, it communicates via interface UART (TX, RX) and the refresh frequency is up to 5 Hz. The module is equipped with straight goldpins.

 

Attention!

The module is not a product of the company u-Blox, it is a version of Wavesharecompatible with u-Blox NEO-7M.

 

The system has soldered straight goldpin connectors and a ceramic antenna.

Key features

  • GLONASS system- the Russian satellite navigation system, covering the entire globe.
  • Simple connection- equipment communicates via simple UART interface i.e. RX and TX pins with default speed of 9600 bps. Thanks to the wide voltage range, it can work with devices 3.3 V, for example, STM32 and Raspberry Pi, and 5 Volts, for example, Arduino
  • Built-in ceramic antenna- gives the sensitivity of -162 dB to increase this parameter, the external version can be attached via the u.FLconnector. Since most of the available antennas have SMA connector, in our offer, you will find a suitable adapter u.FL - SMA.
  • The backupbattery - on the reverse side is a battery to retain data in the device when the supply voltage is disconnected.

 

The manufacturer provides a user manual describing the operation of the module.

 

Connection and sample program

The system has 5goldpin leads - raster 2.54 mm. A description of their functions is in the table below.

 

PinDescription
VCC Supply voltage 3.3 V or 5 V.
GND The ground of the system.
TXD The transmitter of the serial interface which should be connected to the receiver of microcontroller (RX).
RXD The receiver of the serial interface that should be connected to the microcontroller's transmitter (TX).
PPS An optional output of the signal pulse-per-second of the GPS module.

 

 


The module supports such software as: u-center and GoogleEarth.

Specification

  • Supply voltage: from 2.7 V to 5.5 V
  • Current consumption: 35 mA
  • Module NEO-7M-C (documentation)
  • Support of GLONASS system
  • Communication: NMEA, UART 4800, 9600 (by default), 19200, 38400, 57600, 115200, 230400 bps
  • Positioning accuracy: 2.5 m
  • Sensitivity: -162 dBm
  • Update: 5 Hz (by default - 1 Hz)
  • Warm/cold start: 27 seconds / 1 second
  • It has a built-in antenna and a connector for outputting the external u.FL version 

 

Voltage to 2.7 V
Voltage from 5.0 V
Interface UART
GPS - Refreshing 5 Hz
GPS - Accuracy -162 dBm
Test 3
Package width 0.001 cm
Package height 0.001 cm
Package depth 0.001 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: