Grove modules - Strona 2
Grove - a speaker with a digital interface
Speaker module Grove is a device controlled by the PWM signal. It c an work as a simple buzzer or audio player. The volume is adjustable with the built in potentiometer. The...Grove - IR receiver 38kHz 940nm
IR receiver from Grove , operating at a frequency of 38 kHz with a supply voltage from 3.3 V to 5.0 V. Maximum sensitivity is observed for the wave length of 940 nm.Grove - capacitive humidity sensor - corrosion resistant
The device is used to measure the soil moisture by the capacitive detection. It has a built in voltage regulator which provides an operating voltage in the range from 3.3 V to...Grove - set of 5 female-female 4-pin - 2mm/30cm with latch
A set of five 4-pin Grove wires. They are used to connect sensors with Grove Base Shield v2. Cable length is 30 cm. Version with a latch.Grove - 10kΞ© rotary potentiometer linear lower connector
Potentiometer 10 kOhm with linear rotary. It has a 300Β° range of rotation. It has a 4-pin Grove connector on the other side of the handle. The kit includes a cable adapted...Grove - Base Hat for Raspberry Pi - shield for Raspberry Pi 4B/3B+/3B
Overlay for Raspberry Pi 4B / 3B+ / 3B based STM32 microcontroller with 12-bit ADC, with Grove connectors, allows the connection of sensors and modules from the Grove...Grove - LoRa-E5 STM32WLE5JC - EU868/US915 - LoRaWAN radio module - Seeedstudio 113020091
LoRa-E5 radio module with Grove connector, manufactured by Seeedstudio. It features an STM32WLE5JC chip with a low-power 32-bit ARM Cortex M4 processor with a clock...Grove - Shield for micro:bit v2.0
Grove Shield v2.0 overlay for micro:bit features 4 4-pin connectors for easy connection of Grove series sensors to the minicomputer.Grove - GSR sensor - electrical resistance of the skin
Module from the Grove series equipped with GSR sensor using the galvanic-skin reaction. It is powered with the voltage of 3.3 V or 5V. The s ensors of this type are used in...Grove - temperature and humidity sensor DHT11 - Seeedstudio 101020011
The sensor of temperature and humidity DHT11 from the Grove series. The output is a digital signal. The temperature measurement range is from 0 Β°C to 50 Β°C and...Grove - Base Shield for Arduino Nano
Shield for Arduino Nano is a board fully compatible with Seeeduino Nano. It has 8 connectors, so it is possible to connect many devices, sensors, Grove displays using 4-pin...Grove - DS1307 real-time clock I2C
Module from Grove features a real time clock DS1307, which voltage is supplied by a round CR1225 battery (not included) . It allows you to read the time in hours, minutes,...Grove - push button with backlight - blue
Module from the Grove is equipped with a button with a blue LED. Powered with the v oltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...Grove - push button with backlight - red
Module from the Grove is equipped with a button with a yellow led. It is powered with the voltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...Grove - push button with backlight - yellow
Module from the Grove is equipped with a button with a yellow led. It is powered with the v oltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...Grove - vibration motor + module
The module contains a miniature DC vibrating motor. It is very easy to use and is equipped with Grove interface which makes it easy to connect it with Arduino and Raspberry Pi.Grove - analog NTC temperature sensor
Analog sensor is compatible with Arduino and Raspberry Pi. It is powered with the voltage from 3.3 V to 5 V. It can measure temperature in the range from -40 Β°C to 125 Β°C with...Grove - WS2813 RGB LED Strip Waterproof - 60 LED/m - 1m
Waterproof RGB LED strip powered by 5 volt with replaceable silicone case. It consumes a power of 18 W/m, density is 60 diodes per meter. LEDs can also emit cool white light,...Grove - water level sensor - 10cm - Seeedstudio 101020635
Sensor to measure the water level in a vessel up to 10 cm using the Arduino module. The measurement is made by volume . The tile is equipped with a Grove connector, for...Grove - Shield for Seeeduino XIAO - Seeedstudio 103020312
Overlay for Seeeduino Xiao , extending the capabilities of pins I / 0. Provides compatibility of the module with Grove series sensors. It has 8 built-in Grove connectors,...Grove - gesture sensor PAJ7620U2 - 5V I2C
Module from the Grove series, is equipped with a gesture sensor PAJ7620U2 with I2C interface. It can recognize 9 basic gestures. It is powered with the voltage of 5 V. It has a...See also
- Inductive sensors
- Hall effect sensors
- Oxygen sensors
- Optical sensors
- Resistance sensors
- Door sensors
- Piezoelectric sensors
- RPM sensors
- Twilight sensors
- Tilt sensors
- Accelerometers
- Alarm sensors
- 9DoF IMU sensors
- Pressure sensors
- Air quality sensors
- Sound sensors
- Gesture sensors
- Gas sensors
- Limit switches
- Sensors of light and color
- Magnetic sensors
- Medical sensors
- Pressure sensors
- Sensors odbiciowe
- Distance sensors
- Inductive contactless sensors
- Weather sensors
- Liquid level sensors
- Current sensors
- Flow sensors
- Motion sensors
- Temperature sensors
- PT100 temperature probes
- Humidity sensors
- Fingerprint readers
- Encoders
- Photoresistors
- Phototransistors
- IR receivers
- Magnetometers
- Gyros
- Sensor sets
- Gravity modules