- EOL
Attention! The product has been discontinued. Check other products in category. |
Description
The module is equipped witha 32-bitprocessorAtmel ARM Cortex-M0+, 256KB Flash memory and 32KB SRAM.It combines the capabilities of tileMKR Zeroand the connection ofLoRadue to the additional systemMurat CMWX1ZZABZ. The ideal solution for projects requiringwireless network connection or IoT. The device can be supplied with power of5V via USB or pin VIN and two batteriesAAAAA.Switching power sources is automatic without the need of disruption of the operation. The module is fully compatible with the environmentof the Arduino, the only difference is that all pins I/O only work on 3.3 V voltage, the higher voltage may damage the tile. To get wireless connection, you need a GSM antenna connected to the micro uFL slot,which must be purchased separately.
The subject of the sale is the original product for Arduino, Botland isthe official distributor of this company.
Key features
Below are a few features that distinguishWAN MD 1300 from the other programmable tiles.
Feature | Description |
---|---|
Installed bootloader |
Thanks to bootloader, only the appropriatemicrousb cableandthe software from the manufacturer's websiteare necessary to program the device. |
Small size |
This version is characterized by small size: 67,64 x 25 mm. Has soldered male connectors on the bottom and female connectors on the top side of the device. |
Digital I/O |
8 digital inputs/outputs allow, in particular, to control the LEDs, relays and reading the buttons' States. |
Efficiency of current |
The maximum current efficiency for one output is 7 mA. |
Output PWM |
12 outputs PWM allows, for example, to control the motors and brightness the LEDs. |
Analog input |
7 inputs, built-in analog-digital converter with a resolution of 12-bits support, in particular, sensors with analog output. |
Serial communication |
The device supports popular communication interfaces, including UART, I2C and SPI. |
Built-in memory |
Atmel SAMD21 system is clocked with a clock signal at a frequency of 48 MHz, has 256 KB Flash and 32 KB RAM SRAM. |
Supply 5 V microUSB / battery 3.7 V |
To power the Arduino, you can usea power sourcewith a voltage of 5 V with a microUSB connector, pin VIN with voltage ranging from 5 to 6 V or 2 batteriesAA/AAA |
LoRa |
Radio connection, featuring low power consumption and relatively large distance, ideal for IoT devices |
Playing music files |
The module supports playing music files using the SPI interface (SPI1). |
First run To help you get started with the module, we have prepareda tutorialthat will help you with the installation and first run of the Arduino environment. |
Specyfilacja
- CPU: Atmel SAMD21 ARM Cortex-M0+ 32-bit
- Clock frequency: 32.768 kHz (RTC), 48MHz
- Supply voltage (USB/VIN) is 5 V
- Battery power: 2x AA or 2 AAA
- The operating voltage of the pins I/O: 3.3 V
- Digital pins I/O: 8
- Pins PWM: 12
- Supported interfaces: UART, SPI, I2C
- Analog input pins: 7 (ADC 8/10/12-bit)
- Analog output pins: 1 (10 bits DAC)
- Pins supportting external interruptions: 8
- Maximum pins current I/O: 7
- Flash memory: 256 KB
- SRAM: 32 KB
- Built-in LEDs: 6
- Connectors: microUSB, micro uFL, ARK 2x
- The maximum power of the antenna: 2 dB
- Operating frequency: 433/868/915 MHz
- Size: 67,64 x 25 mm
- Weight: 32 g
If you install software downloaded from other source than described on the reverse side of the module, the user will receive a message about an unauthorized provider of tile. You can cancel it with one click, and the environment will be working correctly.
We guarantee that all tiles marked with a symbol Arduino are genuine and come from the same source. As you can see by checkingthe list of authorized distributors. |
Useful links |