• EOL

Evaluation Board with accessories for Particle M.2 SoM

Index: PRE-16807 EAN: 812035030491

Evaluation board designed for IoT Particle B series with M.2 connector. Board with all pins of the main circuit. It is equipped with a USB port for the nRF52840 microcontroller, microSD card slot, Ethernet connector, jack power connector, buttons, RGB LEDs and Li-Pol battery connector.

Evaluation Board with accessories for Particle M.2 SoM
€139.50
€113.41 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Particle

Attention!

The product has been discontinued. Check other products in category.

Product description: Evaluation plate with accessories for Particle M.2 SoM

Evaluation board designed for IoT ParticleBserieswithM.2connector. Board with all pins of the main circuit. It is equipped with a USB port for the nRF52840 microcontroller,microSDcard slot,Ethernet connector, jack power connector, buttons, RGB LEDs andLi-Pol batteryconnector.

Płytka ewaluacyjna dla Particle M.2 SoM

Evaluation board for Particle M.2 SoM.

The device is powered from 5 V to 12 V, the recommended value is5 V / 500 mA(with Li-Pol battery) or5 V / 2000 mA(without battery). The board also hasa charger circuitfor Li-Pol packages. It also supports PoE. The board has an analogue and I2C connector compatible withGrovesystem.

Elements on the Particle evaluation board

Elementy na płytceThe distribution of elements on the board.

N.B.IDDescription
1 External power supply 5 to 12 volts. The minimum recommended is 5 V / 0.5 A (with battery connected) or 5 V / 2 A (without Li-Pol battery connected).
2 Li-Pol battery connector Connect the Li-Pol battery to it.
3 USB SoM port The module's main USB port connected to the microcontroller.
4 JTAG connector Allows you to connect a debugging wire for the Particle module.
5 Battery switch Used to switch the battery operation mode: power / charging.
6 SoM power switch 3.3 V power supply for the SoM.
7 USB u-blox port USB port for u-blox firmware upload.
8 Ethernet connection RJ45 connector for 10 or 100 Mbps Ethernet cable.
9 PoE connector Connected to the Particle PoE adapter, it provides Power-over-Ethernet power.
10 GSM antenna SMA connector forconnecting an external GSM antenna.
11 Bluetooth antenna SMA connector to connect an external Bluetooth antenna.
12 TF/SD card MicroSD card slot.
13 User LED Blue diode connected to pin D7.
14 Reset button Same button as in the Boron module.
15 RGB LED RGB status LED.
16 Mode button Samebutton as in the Boron module.
17 Outlet connector It allows easy access to I/O outputs of the SoM.
18 Analogue port Grove It allows to connect analogue and digital modules of Seeedstudio Grove system.
19 Port I2C grove It allows to connect I2C modules of Seeedstudio Grove system.
20 NFC antenna U.FL connector to connect an optional NFC antenna.
21 J12 jumpers Enable or disable some functions of the evaluation board.
22 SoM connector Connector to connect Boron SoM module.
23 J13 jumpers Enable or disable some functions of the evaluation board.
24 Power Jumpers Enable or disable the power supply from the evaluation board.
25 Charging LED Status light for Li-Pol battery charging.

Block diagram of the board

Schemat blokowy

Block diagram.

Evaluation plate specification for Particle

  • Supply voltage: 5 V to 12 V
  • Compatibility: Particle SoM M.2 Series B - B523 and B402
  • The exits:
    • I/O of the SoM module
    • analog connector Grove
    • I2C Grove connector
  • Li-Pol charging system
  • Dimensions: 125 x 91 x 15.5 mm
  • Weight: 71.8 g (with PoE module)

The set includes

  • Evaluation plate
  • Grove humidity sensor
  • Grove cable
  • 2x U.FL - SMA adapter
  • Set of jumpers
  • MicroUSB cable
  • Screws and washers

Akcesoria zawarte w zestawieAccessories included in the kit.

Voltage to 5.0 V
Voltage from 12.0 V
Package width 14 cm
Package height 10.5 cm
Package depth 3 cm
Package weight 0.156 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: