- EOL
Attention! The product has been discontinued. Check other products in category. |
Description
MinicomputerNanoPi, version M2Awith processor Samsung S5P4418 quad-core ARM Cortex-A9 with a clock frequency of 1.4 GHz. Board has1GB of DDR3 RAM, integratedwi-fi and Bluetooth 4.0, anEthernet Gigabit port,HDMI 1.4A connectorandtwo USB A slot+2 x USB Hoston pins of 2.54 mm,40 GPIOs, slot for microSDcards. It works with theuboot, Android and Debian.
NanoPi M2A has a Ethernet Gigabit port, WiFi and 802.11 b/g/n Bluetooth 4.0 dual-mode module with built-in antenna. |
The advantage of board, is its small size, the outline fits in a rectangle with sides of 64 x 60 mm.
What it takes to run minicomputer NanoPi?
- MicroSD memory card - carrier on which the operating system will be installed
- Power supply unit with a micro usb connector - 5 V with maximum load current 2 A
- HDMI cable- to connect the device to the monitor
- Mouse and keyboard - to control and input data into the device
Operating system
NanoPi works with the systems selected by manufacturer: u-boot and UbuntuCore. The drive of device can be microSD card, which can be purchased in our store.
Operating systems can be downloaded from the manufacturer's website. The manufacturer also provides guide around the installation of the system. |
Communication
Minicomputer has basic communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors of audio and video, the user has at his or her disposal:
- two USBconnectorsA +2x USB Host on pins of 2.54 mm, to which can be connected, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number using an external USB HUB. The interfaces displayed on pinach can be connected using wires.
- EthernetGigabit slot, that is, the ability to directly connect to the LAN network.
- the wi-fi module -it allows for communication with wireless 802.11 b/g/n network.
- Bluetooth 4.0 module- it enables the data transmission through the popular interface.
- 40 pins of GPIO - outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers of motors. Among them are the pins supporting interfaces: I2C, SPI and UART.
- a slot for microSD - slot for memory card microSD on which the operating system can be installed.
- HDMI connector- it transfers image to the monitor.
The device has 2 USB slots, HDMI connector, audio Jack of 3.5 mm, an Ethernet port and many others.
Power
As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 V and output current of the used power supply shall not be less than 2.0 A. In our assortment you will find power supplies that meet these parameters, for example: power supply Extreme 3.1 A.
Minicomputer NanoPi M2A in comparison with the popularRaspberry PiBoard andArduino.
Touch screens
In our offer, available are touch screens dedicated for minicomputers NanPi and NanoPC.
The screen connects through the tape cable, using dedicated LCD slot.
Starter set
The manufacturer has prepareda set of sensors and modulesin a convenient chest that simplifies getting started with minicomputer.
The contents of the setMatrix Starter Kit- sold separately.
Specification |
|
Model | NanoPi M2A |
Specification |
|
Processor | Samsung S5P4418 |
The core |
Quad-Core ARM Cortex A9 |
Systems |
Debian Android uboot |
Clock frequency | 1.4 GHz |
RAM |
1 GB DDR3 32-bit |
Memory |
microSD card |
Power system |
AXP228 PMU |
Slot for GPIO |
40-pin, compatible with Raspberry Pi |
Power |
5 V / 3 A - microUSB |
Board sizes | 64 x 60 mm |
Interfaces | |
USB-Host |
2x USB A slots 2x USB Host on pins of 2.54 mm |
Network interface | Gigabit Ethernet (RTL8211E) |
The Wi-Fi interface | module wi-fi 802.11 b/g/n with antenna |
Bluetooth interface |
Bluetooth 4.0 dual mode |
Video | HDMI 1.4 A, 1080p 60fps |
Audio |
HDMI, audio Jack 3.5 mm |
Camera | DVP, slot of 0.5 mm FPC |
LCD | slot of 0.5 mm SMT FPC (RGB 8-8-8) |
LVDS interface | 20 pin, pitch of 2.0 mm |
Communication |
UART, SPI, I2C, GPIO, PWM |
The debugger |
Serial port of 4pin / 2.54 mm |
Other |
the Power and Reset buttons status LEDs |
Useful links |