- EOL
|
Attention! This product is no longer available for sale. Check out the other SBC minicomputers in this category. |
Description
Duo version NanoPiminicomputer withAllwinner H2+ quad-coreARMCortex-A7 1.2 GHz processor. The board has 256 MB ofDDR3 RAM, built-in WiFi+ 2x USB Host on2.54 mm pins,16 x 2 GPIO, connector for microSD card. It works withUbuntuCore and Linuxvendor systems.
The advantage of the board is its small dimensions, board outline is 50 x 25,4 mm.
What do you need to run NanoPi minicomputer?
- AmicroSD memory card- the medium on which the operating system will be installed
- Power supply with a microUSB plug- 5 V with a current capacity of 2 A
The device has a WiFi module and other popular interfaces.
Operating system
NanoPi works with systems prepared by the manufacturer: UbuntuCore and Linux Lastest Mainline Kernel 4.11. The drive of the device can be a microSD card, which can be purchased in our store.
|
The operating systems can be downloaded from the manufacturer'swebsite. The manufacturer also providesa guide to installing the system. |
Communication
The minicomputer has the basic communication interfaces that can be found in PC-class office computers. In addition to the previously mentioned audio and video connectors, the user has at his disposal:
- 2x USB Host on 2.54 mm pins, under which you can connect, for example, a mouse, keyboard, WiFi card or flash drive. If it turns out that there are not enough sockets, you can increase their number by usingan external USB HUB. The interfaces can be connected with wires to the pins.
- WiFi module- wireless communication in 802.11b/g/n standard
- Ethernet connector 10 / 100 MHz for pinout 2.54 mm
- GPIO x 16 pins x 2- general purpose outputs/inputs that can be used to operate LEDs, buttons, motor drivers. Among them there are pins supporting I2C, SPI and UART interfaces. 2.54mm goldpin pins are soldered in factory.
- microSD slot- a slot for a microSD memory card, on which operating system can be installed.
GPIO pinout - the module has already soldered goldpin pins.
Power supply
The module uses microUSB connector as power source. The manufacturer recommends that the voltage given to the connector is 5.0 V and the current capacity of the power supply used should be at least 2.0 A. In our offer you will findpower supplies meeting these parameters, for example:Extreme 2.1 A power supply.
Starter kit
The manufacturer has prepareda set of sensors and modules in a handy case that makes it easy to start working with a minicomputer.
Matrix Starter Kit contents - to be purchased separately.
Specifications |
|
| Model | NanoPi Duo |
| Specifications |
|
| Processor | Allwinner H2+ |
| Core |
Quad-Core ARM Cortex A7 |
| Systems |
Linux Kernel 4.11.2 UbuntuCore |
| Clocking | 1.2 GHz |
| RAM |
256 MB |
| Memory |
microSD card |
| GPIO socket |
16 pin 2.54 mm connector soldered on the board |
| Power supply |
5 V / 2 A - microUSB |
| Board dimensions | 50 x 25.4 mm |
| Interfaces | |
| USB Host |
2 x USB Host on 2.54 mm pin |
| Network interface | Ethernet 10/100 Mbps on2.54mm pin |
| Video | -CVBS on GPIO pins |
| Audio |
audio and microphone output pin out on GPIO connector |
| Communication |
WiFi, UART, SPI, I2C, GPIO, PWM |
| Debugger |
Serial port 4pin / 2.54mm |
| Additional |
Reset button, u.FL connector for additional antenna |
Useful links |
