- EOL
Attention! The sale of the product has been completed. Check otherdevices in this category. |
Description
NanoPimini-computerin M3 versionwith Samsung S5P6818 octa-core ARM Cortex-A53 1.4 GHz processor. The board has1 GB of DDR3 RAM, built-in WiFiand Bluetooth 4.0module,Ethernet Gigabitport,HDMI 1.4A connector and2USB A + 2xUSB Hostportson2.54 mm pins, 40 GPIO,microSD card slot.Works withbots, Android and Debian.
NanoPi M3 has a Gigabit Ethernet port, WiFi module and 802.11b/g/n Bluetooth 4.0 dual-mode with built-in antenna. |
The advantage of the board is its small dimensions, the outline fits into a rectangle with sides of 64 x 60 mm.
What do you need to run a NanoPi minicomputer?
-
MicroSD memory card- the media on which the operating system will be installed
-
Power supply unit with microUSB- 5 Vplugwith 3 A current capacity
- HDMI cable - toconnect the device to a monitor
- Mouse and keyboard- to control and enter data into the device
Operating system
NanoPi is compatible with the bug systems, Android and Debian. The disk of the device can be a microSD card, which can be purchased in our shop.
Operating systems can be downloaded fromthe manufacturer's website. The manufacturer provides asystem installation guide. |
Communication
The minicomputer has basic communication interfaces that can be found in PC-class office computers. In addition to the previously mentioned audio and video interfaces, the user has the possibility to use them:
- two USBA +2x USB Hostconnectorson 2.54 mm pins, under which you can connect e.g. a mouse, a keyboard, a WiFi card or a flash drive. If it turns out that there are too few sockets, you can increase their number usingan external USB HUB. The interfaces on the pins can be connected with cables.
- GigabitEthernet socket, i.e. possibility of direct connection to the LAN.
- WiFi module- allows for communication with 802.11b/g/n wireless network.
- Bluetooth 4.0 module- enables data transmission via a popular interface.
- GPIO x 40 pin- general purpose outputs/inputs, which can be used to operate LEDs, buttons, motor controllers. Among them there are pins supporting the interfaces: I2C, SPI and UART.
- microSD slot- slot for a microSD memory card, on which the operating system can be installed.
- HDMI connector- transmits video to the monitor.
The device has 2 USB ports, HDMI, 3.5 mm audio jack and Ethernet port and many others.
Power supply .
The system uses the microUSB connector as the power source. The manufacturer recommends that the voltage given on the connector should be 5.0 V, while the current capacity of the power supply used should be at least 2.0 A. In our offer you will findpower supplies meeting these parameters, e.g.:Extreme 3.1 A power supply.
NanoPi M3 minicomputer against the background of the popular RaspberryPi andArduino tiles.
Touchscreens
Our offer includestouchscreens dedicated to NanPi and NanoPC minicomputers.
The screen communicates through a tape cable using a dedicated LCD socket.
Starting set
The manufacturer has prepared aset of sensors and modules in a handy trunk, which makes it easy to start working with a mini-computer.
Contents of theMatrix Starter Kit- available separately.
Specification |
|
Model | NanoPi M3 |
Specification |
|
Processor | Samsung S5P6818 |
Core |
Quad-Core ARM Cortex A53 |
Systems |
Debian Android Slaughterhouse |
Clocking | 1.4 GHz |
Memory RAM |
1 GB DDR3 32-bit |
Memory |
microSD card |
Power supply system |
AXP228 PMU |
GPIO socket |
40 pins, Raspberry Pi compliant |
Power supply |
5 V / 3 A - microUSB |
Dimensions of the tiles | 64 x 60 mm |
Interfaces | |
USB Host |
2x USB A sockets 2x USB Host on 2.54 mm pins |
Network interface | Ethernet Gigabit (RTL8211E) |
WiFi interface | WIFi 802.11b/g/n module with antenna |
Bluetooth interface |
Bluetooth 4.0 dual mode |
Video | HDMI 1.4A, 1080p 60fps |
Audio |
HDMI, audio Jack 3.5mm |
Camera | DVP, 0.5 mm FPC socket |
LCD | 0.5 mm SMT FPC socket (RGB: 8-8-8) |
LVDS interface | 20 pin, 2.0 mm raster |
Communication |
UART, SPI, I2C, GPIO, PWM |
Debugger |
Serial port 4pin / 2.54mm |
Other |
Power, Reset buttons status LEDs |
Useful links |