|
Attention, the sale of the product is complete! Orange Pi minicomputers have been withdrawn from sale due to the manufacturer's failure to provide appropriate certification. We encourage you to familiarize yourself withother devices available in our offer. |
Description
Orange Pi mini-computer in Plus version with powerful AlwinnerH3 quad-core ARM Cortex-A7processor.The board has1 GB of DDR3 RAMand 8 GBEMMC, WiFi, 10/100Mbps Ethernet port,HDMI portand3xUSB Host, 1xmicroUSB OTG, 40 GPIO,microSD card and IR receiver connectors. Works withUbuntu or Android 4.4systems.
The device has 3 USB ports, HDMI and Ethernet port and many others.
What do you need to run an Orange Pi minicomputer?
- MicroSD memory card- the medium on which the operating system will be installed.
- Power supply- with 5 V output voltage and 4.0 x 1.7 mm DC plug
- Enclosure- protects the minicomputer from external conditions
- HDMI cable - toconnect the device to a monitor
- Mouse and keyboard- to control and enter data into the device
Additional accessoriesare also available in our shop.
Operating system
Orange Pi works with Ubuntu and Android 4.4 systems and systems known from Raspberry Pi. The device can be a microSD card with a capacity up to 64 GB or 8 GB of built-in EMMC Flash memory.
|
Ubuntu and Android systems can be downloaded fromthe manufacturer's website. There is also available an interestingArmbian andOpenELEC system. Installation of the system is very easy -check our manual! |
Orange Pi PC Plus - top view.
Communication
Orange Pi has basic communication interfaces, which can be found in PC-class office computers. In addition to the previously mentioned audio and video interfaces, the user has at his disposal:
- three USB connectors and one microUSB OTG socket,under which you can connect e.g. a mouse, a keyboard, a WiFi card or a flash drive. If it turns out that there are too few sockets, you can increase their number usingan external USB HUB.
- Ethernet socket, i.e. the possibility of direct connection to the LAN.
- Built-in WiFi module- Raltek for frontless communication, there is also an antenna on the board.
- GPIO x 40 pin- general purpose outputs/inputs that can be used to operate LEDs, buttons, motor controllers. Among them there are pins supporting interfaces: I2C, SPI and UART.
- microSD slot- slot for a microSD memory card, on which the operating system can be installed.
- HDMI output- allows to output video and audio signal to the monitor.
- 3.5 mm jack output- to connect headphones or speakers.
- Built-in microphone- enables sound recording and e.g. making calls.
- CSI input- to connect a dedicated camera.
Power supply .
The system uses a 4.0 / 1.7 mm DC Jack connector as its power source. The manufacturer recommends that the voltage given on the connector should be 5.0 V, while the current capacity of the power supply used should be at least 2.0 A (the manufacturer recommends 3.0 A). In our offer you will find a dedicatedpower supply.
Specification
| Basic information | ||||
 |
 |
 |
 |
|
| Model | ||||
| Specification |
||||
| Processor | Allwinner H3 | Allwinner H3 | Allwinner H3 | Allwinner H3 |
| Core |
Quad-Core ARM Cortex A7 |
Quad-Core ARM Cortex A7 |
Quad-Core ARM Cortex A7 |
Quad-Core ARM Cortex A7 |
| Graphics |
Mali400MP2 GPU @600MHz OpenGL ES 2.0 |
Mali400MP2 GPU @600MHz OpenGL ES 2.0 |
Mali400MP2 GPU @600MHz OpenGL ES 2.0 |
Mali400MP2 GPU @600MHz OpenGL ES 2.0 |
| Systems |
Ubuntu Android |
Ubuntu Android |
Ubuntu Android 4.4 |
Ubuntu Android 4.4 |
|
Memory RAM |
512 MB DDR3 SDRAM |
512 MB DDR3 SDRAM |
1 GB DDR3 SDRAM |
2 GB DDR3 SDRAM |
| Memory |
microSD card up to 64 GB |
microSD card up to 64 GB |
microSD card up to 64 GB +8 GB EMMC |
microSD card up to 64 GB +16 GB EMMC |
|
Node GPIO |
40-pin connector + 3 pin UART |
40-pin connector + 3 pin UART |
40-pin connector + 3 pin UART |
40-pin link
+ 3 pin UART |
| Power supply |
5 V / 2 A (3A recommended) DC Jack |
5 V / 2 A (3A recommended) DC Jack |
5 V / 2 A (3A recommended) DC Jack |
5 V / 2 A (3A recommended) DC Jack |
| Buttons | Power | Power | Power |
Power UBoot IR input |
|
Dimensions
|
69x48mm | 69x48mm | 85x55mm | 108x67mm |
| Interfaces | ||||
| USB Host |
1 x USB 2.0 socket type A |
2 x USB 2.0 socket type A |
3 x USB 2.0 socket type A |
3 x USB 2.0 socket type A |
| USB OTG | 1x microUSB | 1x microUSB | 1x microUSB | 1x microUSB |
|
Interface network |
Ethernet 10/100 Mbit/s |
- |
Ethernet 10/100 Mbit/s |
Ethernet 1000 Mbit/s |
|
Module WiFi |
- |
Embedded Realtek aerial |
Embedded Realtek aerial |
Embedded Realtek RTL8189ETV aerial |
| Video |
HDMI, HDMI CEC, CVBS |
HDMI, HDMI CEC, CVBS |
HDMI, HDMI CEC, CVBS |
DMI,
HDMI CEC, CVBS HDMI and CVBS |
| Audio |
HDMI |
HDMI |
HDMI 3.5 mm jack microphone |
HDMI 3.5 mm jack microphone |
| Interfaces |
UART, GPIO |
UART, GPIO |
UART, GPIO |
UART, GPIO |
Useful links |
