|
Attention, the sale of the product is complete! Orange Pi minicomputers have been withdrawn from sale due to the manufacturer's failure to provide appropriate certification. We encourage you to familiarize yourself withother devices available in our offer. |
Description
Orange Pi Zero Minicomputer with powerfulH2 quad-core ARM Cortex-A7processor. The board has512 MBDDR3RAM,WiFi module,10/100Mbps Ethernetport and1x USB Host,1x microUSB OTG, 26 GPIO,microSDcard slot. Works withAndroid, Lubuntu, Debian, Raspbian.
The device has 1 USB port and Ethernet port and many others.
What do I need to run an Orange Pi minicomputer?
- MicroSD memory card- the media on which the operating system will be installed.
- Power supply unitwith microUSB plug - with 5 V output voltage
Operating system
Orange Pi works with Ubuntu and Android systems and systems known from Raspberry Pi. The device can be a microSD card with a capacity of up to 64 GB.
|
Ubuntu and Android systems can be downloaded fromthe manufacturer's website. There is also available an interestingArmbiansystem. Installation of the system is very simple -check our manual! |
Orange Pi Zero - top and bottom view.
Communication
Orange Pi has basic communication interfaces, which can be found in PC-class office computers. In addition to the previously mentioned audio and video interfaces, the user has at his disposal:
- one USB connector and one microUSB OTG socket,where you can connect e.g. a mouse, a keyboard, a WiFi card or a flash drive. If it turns out that there are too few sockets, you can increase their number usingan external USB HUB.
- WiFi module- XR819, for wireless communication in IEEE 802.11 b/g/n standard
- Ethernet socket, i.e. possibility of direct connection to the LAN.
- GPIO x 26 pin + 13 pin connector- general purpose outputs/inputs that can be used to operate LEDs, buttons, motor controllers. Among them there are pins supporting interfaces: I2C, SPI and UART.
- microSD slot- a slot for a microSD memory card, on which the operating system can be installed.
Power supply
The system uses a microUSB socket connector as its power source. The manufacturer recommends that the voltage given on the connector should be 5.0 V, while the current capacity of the power supply used should be at least 2.0 A. In our offer you will findappropriate power supplies.
Specification
| Basic information | ||
 |
|
|
| Model | ||
| Specification |
||
| Processor | H2 | H2 |
| Core |
Quad-Core ARM Cortex A7 |
Quad-Core ARM Cortex A7 |
| Graphics |
Mali400MP2 GPU @600MHz OpenGL ES 2.0 |
Mali400MP2 GPU @600MHz OpenGL ES 2.0 |
| Systems |
Ubuntu Android |
Ubuntu Android |
|
Memory RAM |
256 MB DDR3 |
512 MB DDR3 |
| Memory |
microSD card up to 64 GB |
microSD card up to 64 GB |
|
Node GPIO |
26-pin connector + 13 pin |
26-pin connector + 13 pin |
| Power supply |
5 V / 2 A microUSB |
5 V / 2 A microUSB |
| Buttons | Power | Power |
|
Dimensions
|
48x46mm | 48x46mm |
| Interfaces | ||
| USB Host |
1 x USB 2.0 socket type A |
1 x USB 2.0 socket type A |
| USB OTG | 1x microUSB | 1x microUSB |
|
Interface network |
Ethernet 10/100 Mbit/s |
Ethernet 10/100 Mbit/s |
|
Module WiFi |
Embedded XR819 aerial |
Embedded XR819 aerial |
| Video | - | - |
| -Audio | microphone |
microphone |
| Interfaces |
UART, GPIO |
UART, GPIO |
Useful links |
