• EOL

Waveshare GSM/GPRS/GPS SIM908 Shield - overlay on Arduino

Index: WSR-04660

Overlay for Arduino with SIM908 chip, which allows you to send text messages, create GSM network connections, transfer GPRS data and read GPS position. It communicates through serial interface UART (RX, TX) via AT commands, GPS antenna, power supply and miniUSB cable are included.

Waveshare GSM/GPRS/GPS SIM908 Shield - overlay on Arduino
€59.00
€47.97 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Waveshare
Compatibility: Arduino

Attention!

The sale of the product has been completed. Check thenew version.

Description

Overlay for Arduino with SIM908 chip, which allows you to send text messages, create GSM network connections, transfer GPRS data and read GPS position. It communicates through serial interface UART (RX, TX) via AT commands. The board is equipped with: SIM card connector, microphone, speaker, and miniUSB connector. The kit also includes aGPSantenna,9V / 2A power supply and miniUSB cable.

GPS/GPRS/GSM Shield dla Arduino

Detailed description of the module connection is available in the user guide.

Connection

The chip works with Arduino tiles, e.g. Uno version.Built-in USB - UART converter, allows for direct communication with the computer via AT commands using the includedminiUSB cableand serial port terminal.

What is on the board?

GPS/GPRS/GSM Shield dla Arduino - schemat

  1. Headphone jack input: output of the second analog voice channel SIM908
  2. SMA connector for GSM antenna
  3. Pins to connect with Arduino
  4. GSM antenna connector
  5. SIM908 control interface
  6. GPS antenna connector
  7. USB-UART interface
  8. Loudspeaker: output of the first analogue voice channel SIM908
  9. Reset Arduino
  10. SIM908 chip
  11. SIM908 chip LED: when slowly blinking, the network connection has been successful
  12. Power supply LED
  13. Microphone: input of the first analogue voice channel SIM908
  14. SIM card slot
  15. CP2102: USB-UART converter
  16. LEDs for UART transmission
  17. Power switch
  18. Power connection from 6 V to 9 V
  19. Motor to generate vibrations
  20. 74HC125 - GSM and GPS control management via serial port
  21. NCP2890 power amplifier: amplifies the first analogue voice channel SIM908
  22. MIC29302
  23. SIM908 analog output jumper (positive): open when NCP2890 is on
  24. SIM908 analog output jumper (negative): open when NCP2890 is on
  25. NCP2890 jacks:
  • Compact EN and VBAT: on
  • Compact EN and GND: system off

Specification

  • Power supply voltage:
    • GSM: 3.2 to 4.8 V
    • GPS: 3.0 to 4.5 V
  • UART communication
  • Support for AT commands
  • Built-in USB - UART CP2102 converter with miniUSB socket (cable included)
  • GSM chip SIM908
    • Supported bands: 850 / 900 / 1800 / 1900 MHz
    • GPRS class 10: up to 85.6 kb/s
  • 42-channel GPS
    • Affection: -160 dBm
    • Cold start: 30 sec
    • Hot start: 1 s
    • Accuracy: up to 2.5 m
    • Current consumption (GSM at standstill): 77 mA
  • Built-in microphone and speaker
  • 74HC125 - GSM and GPS control management via serial port
  • Detection of ear closeness and vibrations
  • Operating temperature: -40 to 85 °C
  • Removing the echo effect
  • The overlay works with Arduino tiles, for example Arduino Uno
  • Module dimensions: 100 x53 mm

The kit includes:

  • GSM/GPRS/GPS Shield
  • GPS antenna
  • GSM antenna
  • Guest compartment
  • Mounting screws
  • 9 V, 2 A power supply
  • MiniUSB - USB cable

Test 4
Package width 0.001 cm
Package height 0.001 cm
Package depth 0.001 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: